ALL MANUFACTURERS

Analog Input Terminal Board

4-20 mA current loops
0-5 V or 0-10 V DC voltage signals
Operating Temperature Range: -30°C to +65°C
Storage Temperature Range: -40°C to +85°C
Humidity: 5% to 95% RH, non-condensing

Turbine Protection Input Terminal Board

Series: Mark VIe
Simplex Primary Turbine Protection Input Terminal Board
Number of inputs: 4
Number of outputs: 2
MPU pulse rate range: 2 Hz to 20 kHz
Contact voltage sensing: 20 V dc
Technology: Surface mount
Temperature: -30 to +65C

Low Frequency Velocity Sensor

Individual M8 x 1 
mountingadapter
Sensitivity 20 mV/mm/s (508mV/in/s) ±10%
VelocityRange102 mm/s (4 in/s) peak
AmplitudeLinearity±3%—102 mm/s (4 in/s) peak
Output BiasVoltage-12 ±1 VDC
ShockSurvivability981 m/s2 (100g) peak
Casematerial300 series stainless steel.

Drive Board

Voltage Range:  24V DC 
Operating Frequency: 50Hz or 60Hz
Operating Temperature Range: -10°C to +50°C
Storage Temperature Range: -20°C to +70°C

Central Processing Unit

Part Number IC695CPE305
Form Factor Backplane
User Memory 6MB
I/O32k Bits Discrete I/O, 32k Words for Analog I/O
Energy PackIncluded
Redundancy SupportMedia Redundancy (MRP) with PNC001
Ethernet Port2 - 2 port switch 10/100/1000
Ethernet ProtocolsSRTP Client/Server, 
Modbus TCP/IP, OPC UA , EGD, PROFINET, 
DNP3 Outstation, IEC-61850 Client, 
IEC-104 Server,HART passthrough

Part Number IC695ETM001
Specialty ModuleRX3i Ethernet module 
10/100 Mbits 2 RJ45 connections one IP 
address occupies one slot on system base
Current Consumption
840 mA @ 3.3 VDC; 614 mA @ 5 VDC
Operational NotesUniversal Backplane Only. 
Uses PCI Bus. Client/Server

Remote Input Module

Number of Channels: 8 digital output channels
Output Voltage Range: 24 VDC ± 20%
Output Current: Maximum 1 A per channel
Power Supply Voltage: 24 VDC
Communication Interface: 
Dual RBUS for high-speed data transfer

Remote DIGITAL OUTPUT MODULE

Number of Channels: 8 digital output channels
Output Voltage Range: 24 VDC ± 20%
Output Current: Maximum 1 A per channel
Power Supply Voltage: 24 VDC
Communication Interface: 
Dual RBUS for high-speed data transfer

Remote Multi-Purpose Input/Output Module

Input supply voltage: 24 VDC (18-31.2 V)
Loop voltage: Input supply voltage
Input loop current: Max. 4 mA @ 24 VDC 
loopvoltageChannel "Off" current: <0.5 mA
Channel "On" current: >3 mA
Max input voltage: Input supply voltage
Max. input signal freq.: 10 ms pulse
Compliance: Namur comp 

Remote MultipurposeInput/Output

Input supply voltage: 24 VDC (18-31.2 V)
Loop voltage: Input supply voltage
Input loop current: Max. 4 mA @ 24 VDC 
loopvoltageChannel "Off" current: <0.5 mA
Channel "On" current: >3 mA
Max input voltage: Input supply voltage
Max. input signal freq.: 10 ms pulse
Compliance: Namur comp 

BUS MODULE

Power Supply Voltage: 
10 to 28.8 VDC from SPBus
Operational Temperature Range: -15°C to +70°C
Storage Temperature Range: -25°C to +70°C
Relative Humidity: Up to 98%

Remote DigitalInput/Output and relay

Input supply voltage: 24 VDC (18-31.2 V)
Loop voltage: Input supply voltage
Input loop current: Max. 4 mA @ 24 VDC loopvoltage
Channel "Off" current: < 0.5 mA
Channel "On" current: > 3 mA
Max. input voltage: Input supply voltage
Max. input signalfreq.: 10 ms pulses

Remote Analogue Input, Current

Number of channels: 32 current inputs
Current input: 0-20 mA (input resistor 220 ohm)
Current accuracy: +/- 0.2% of full scale
(resistor accuracy = 0.1%)
Current input lter: RC = 33 µs
Digital resolution: 12 bits
Connectors: screw terminals, 2.5 mm

Remote Digital Input and Output

Input voltage: 24 VDC ±20%
Power consumption: maximum 20 W
Connectors: screw terminals, 1.5 mm
operational: 0° C to 70° C
storage: -25° C to 70° C
Power supply voltage: 10 to 28.8 VDC
SPBus connector: 9-pin male DSUB

Remote Controller Unit

Input voltage: 24 VDC ±20%
Power consumption: maximum 20 W
Connectors: screw terminals, 1.5 mm
operational: 0° C to 70° C
storage: -25° C to 70° C
Power supply voltage: 10 to 28.8 VDC
SPBus connector: 9-pin male DSUB

Remote Controller Unit

Input supply voltage: 24 VDC(+30%, -25%)
Nominal current consumption: ≈ 0.8 A
Start-up current: Max. 2.7 A
Power consumption: Max. 20 W
Heat dissipation: Max. 20 W

Remote Controller Unit

REMOTE CONTROLLER UNIT
32 I/O CHANNELS
32-BIT CPU RUNNING AT 400 MHZ
16 MB FLASH MEMORY
24 VDC
400 MH
20 W
(601418)

Remote Control Unit

REMOTE CONTROLLER UNIT
32 I/O CHANNELS
32-BIT CPU RUNNING AT 400 MHZ
16 MB FLASH MEMORY
24 VDC
400 MH
20 W
(601418)

Remote DigitalInput/Output and relay

Input supply voltage: 24 VDC (18-31.2 V)
No. of I/O channels: 32
Loop voltage: Input supply voltage
Input loop current: Max. 4 mA @ 24 VDC loopvoltage
Channel "Off" current: < 0.5 mA
Channel "On" current: > 3 mA
Max. input voltage: Input supply voltage
Max. input signalfreq.: 10 ms pulses

Remote MultipurposeInput/Output

Voltage input range: 0-4 V, 0-10 V
Input resistor to ground: 3 MΩ
Current input range: 0-20 mA
Automatic protection: 26 m
AInput resistor to ground: 150 Ω ±1 %
Measurement accuracy: ±0.15% of full scale

Remote Controller unit

IACS E10
DnV GL 2.4
IEC 60945
RoHS Directive 2011/65/EU
EMC Directive 2014/30/EU
Input supply voltage: 24 VDC (+30%, -25%)
Nominal current consumption: Max. 0.75 A
Start-up current: Max. 2.8 A
Power consumption: Max. 20 W
Power connectors: Screw terminals (slotted)
Cable cs: 2.5 mm²

OIL MIST DETECTOR PCB BOARD

Input Voltage: 24V DC
Operating Temperature: -10°C to +60°C
Humidity: 5% to 95% relative humidity
VN 115/87 300 553/00 PCB board

MODULE RACK BACKPLANE

Power Input:  24V DC
Ethernet, CAN bus
Operating Temperature: -10°C to +60°C
19-inch rack mountin
DIN rail mounting

BRIDGE CONTROL SYSTEM

300V Class 2 Thin
22 and 24 AWG Stranded Tinned Copper
100% individually foil shielded 
+ overall 65% TC Braid
Drain Wire
PVC Insulation (Power)
FPE Insulation (data)
Lt Gray sunlight / oil resistant PVC jacket
Thin 75oC 

PC Board

Voltage Rating:  
5V DC to 24V DC
Operating Temperature: 
-20°C to +70°C