General Electric

Exciter DC Feedback Board

Voltage Feedback: 0–500 V DC
Current Feedback: 0–10 A DC
Accuracy: ±0.25% of full scale
Frequency Response: Up to 100 Hz
Signal-to-System Isolation: 1500 V AC
Common-Mode Rejection: >60 dB at 50/60 Hz
Analog Output: 4–20 mA or 0–10 V DC

RSTi-EP CPE100 Standalone Controller

Part Number:EPSCPE100
Storage:1MB
I/O:2k Bits Discrete I/O, 32k Words for Analog I/O
Media Redundancy Protocol (MRP)
SRTP Client/Server (Max 8 Connections)
Modbus TCP/IP (Max 8 Connections)
OPC-UA Server (Max 8 Clients)
EDG (Max 16 Exchanges)
PROFINET (Max 8 IO Devices)
Ethernet Port:1x 10/100, 1x 3-port switch 10/100

Power Supply module

Power Supply:40 Watts
Nominal Rated Voltage:120/240 VAC or 125 VDC
Input Voltage Range:18 to 30 VDC
Input Power:60 Watts maximum at full load
Outputs:3
Ripple:150 mV
Output Current:5.1 VDC
Noise:150 mV
Isolation None
Number of Daisy-Chained PSD140:Up to 4
Terminal Current:6 Amps

PACSystems RX7i controller

Application:Rx7i PLC System
Random Access Memory (RAM):64 MB
Operating Voltage:+5, +15, -12 Volt DC
Flash Memory:64 MB
Current Rating:3.4 Amps
Discrete I/O memory:32 K
Microprocessor:600 MHz Pentium M
Analog I/O memory:32 Kwords
CPU Memory:64 Megabytes
Compatible Memory storage:SRAM, Flash
User Memory:64 Megabytes
Processor speed:600 MHz
Max Program Block:512 Program Blocks

Control Module

Supply Voltage: 24 VDC
Isolation: 1500 VAC 
Operating Temperature: -40°C to +70°C
Enclosure Rating: IP20
Backplane Compatibility: PACSystems RX3i racks

PACSystem RX7i power supply module

Series:PACSystem RX7i
Description:Power supply module
Part Number:IC698PSA100
Voltage:120/240 Volts AC, 125 Volts DC
Product Description:Power Supply module
Mounting:Leftmost slot
Input Voltage Range:85 to 264 VAC; 100-150VDC
Power Rating:125 Watts
Output Voltage:5/12, -12 Volts DC
AC Input Frequency:47-63 Hz
Power Factor:0.99 min

Digital input module

Sinking or Sourcing: 24 VDC 
Isolation:1500 VAC
Input Current: 24 VDC
Operating Temperature: -40°C to +70°C
VersaMax I/O: Installed in IC200 or IC600 racks

VersaMax CPUE05 with Ethernet Interfaces

Series:VersaMax
Part Number:IC200CPUE05
Description:CPU module
Modules:64
I/O points:2048
Serial ports:RS 232, RS 485
Boolean Execution Speed:0.8 milliseconds
Memory:64 K bytes
SRTP Server:8 connections
Ethernet Port:One (1) RJ45 port
Ethernet Transmission:10 Mbps, full / half duplex
EGD configuration:32 configurations

VersaMAx controller module

Series:VersaMax
Part Number:IC200CPUE05
Description:CPU module
Modules:64
I/O points:2048
Serial ports:RS 232, RS 485
Boolean Execution Speed:0.8 milliseconds
Memory:64 K bytes
SRTP Server:8 connections
Ethernet Port:One (1) RJ45 port
Ethernet Transmission:10 Mbps, full / half duplex
EGD configuration:32 configurations

Control Circuit Board

30 NM Power Converter ACB AAA
Power Converter (30 NM ACB AAA
Input Voltage: Likely 480 VAC
Output Power: Estimated 30 kW 
Efficiency: ≥95%
Voltage Levels: 5 VDC, 24 VDC
Operating Temperature:-20°C to +60°C
Humidity:5–95% RH (non-condensing)

Printed circuit board

Series: Mark VIe
Product type: Printed Circuit Board
COM Ports: 3; COM1, COM2, and micro-miniature 9-pin socket D connector
Ethernet Interfaces: 10BaseT/AUI connector
Manual: GEP-9145
Relative Humidity: 10-95%, non-condensing
Shock: maximum 10G, non-operating
Female Plug Connectors: 2
No.of Metal Oxide Varistors: 4
Power Supply Rating: 125 VDC

Printed circuit board

Power Supply:24 VDC
Signal Handling:4–20 mA, 0–10 VDC
digital signals:24 VDC logic
Resolution:16-bit ADC/DAC resolution
Operating Temperature:
-40°C to +70°C (-40°F to +158°F)
Humidity:5–95% relative humidity

Wind Turbine Board

Manufacturer:GE Energy
Series:Mark VIe Speedtronic
Part Number:IS200WEORG1A
Functional Acronym:WEOR
Functional Description:GE Printed Circuit Board
PCB Coating:Normal Coating

Printed circuit board

Power Supply: 24 VDC 
analog inputs/outputs:4–20 mA, 0–10 VDC
Resolution:16-bit ADC/DAC
Operating Temperature:
-40°C to +70°C (-40°F to +158°F)
Humidity:5–95% relative humidity 

Printed circuit board

Manufacturer:GE Energy
Series:Mark VIe Wind
Part Number:IS210AEBIH3B
Functional Acronym:AEBI
Functional Description:Alternative Energy Bridge Interface
PCB Coating:Conformal Coating
AEBI:CARD GE WIND TURBINE
Input Voltage: 24V DC
Operating Temperature: Typically between -30°C to +65°C
Humidity: Typically 0-95% (non-condensing)

I/O EXPANSION BOARD

Power Supply:24 VDC 
I/O Channels: 4–20 mA, ±10 VDC
Typical expansion capacity: 16–32 channels
Operating Temperature:-40°C to +70°C (-40°F to +158°F)
Humidity:5–95% relative humidity

Input terminal board

Series: EX2100
Product Type: Alternative Energy Application D
Number of channels: 6
Input Span: 1-5 V dc
Outputs: 24 V outputs
Technology: Surface Mount
Analog output current: 0-20 mA
Operating temperature: -30 to 65 °C

Multiple Application Converter Control Board

Input Voltage:Typically 24 VDC
Signal Compatibility:
Analog: 4–20 mA, 0–10 VDC
Digital: 24 VDC logic
Analog resolution: 12-bit to 16-bit 
Operating Temperature:
-40°C to +70°C (-40°F to +158°F)
Humidity:5–95% relative humidity 

Analog input module

Input Channels:16 single-ended
Input Signal Types:4–20 mA current loops
Resolution:16-bit resolution
Accuracy:±0.1% of full-scale range
Operating Temperature:
-40°C to +70°C (-40°F to +158°F)
Humidity:5–95% relative humidity (non-condensing)

Analog input module

Input Channels:16 single-ended
Input Signal Types:4–20 mA current loops
Resolution:16-bit resolution
Accuracy:±0.1% of full-scale range
Operating Temperature:
-40°C to +70°C (-40°F to +158°F)
Humidity:5–95% relative humidity (non-condensing)

BPPS Board Assembly

Input Voltage Range:24 VDC
Designed to support 24 VDC battery banks
Output Voltage:+5 VDC, ±15 VDC
Operating Temperature:-40°C to +70°C (-40°F to +158°F) 
Humidity: Operates reliably at 5–95% relative humidity

WIND ENERGY MAIN CABINET CARD

Series: Mark VIe
Type: Wind Energy Main Cabinet Board
Input Voltage: Typically 24 VDC
Operating Temperature Range: -30°C to 65°C (-22°F to 149°F)
Storage Temperature Range: -40°C to 85°C (-40°F to 185°F)

Relay Output Terminal Board

Input Voltage: 24 VDC (nominal)
Output Voltage: 24 VDC (typically)
Output Current: 1-2A per relay
Relay Type: SPDT (Single Pole Double Throw) relays
Number of Relays: 8 (Typically, each with individual output terminals)
Relay Contact Rating:
Max Switching Voltage: 250 VAC or 30 VDC
Max Switching Current: 5A (AC or DC)
Max Switching Power: 120VA (AC) or 120W (DC)

Analog Input/Output Terminal Board

Manufacturer:General Electric
Series:Mark VIeS
Part Number:IS200TBAIS1C
Functional Acronym:TBAI
Functional Description:Analog Input/Output Terminal Board
PCB Coating:S-style PCB coating

Rack Module

IC610CHS134
DISCONTINUED BY MANUFACTURER
RACK
24VDC POWER SUPPLY (10 SLOTS)