General Electric

Input Module

Series:Series 90-30
Brand:GE Fanuc
Accuracy:0.1 % full scale
Part Number:IC693ALG221
No of Channels:4
Range:4-20 mA, 0-20 mA
Update Rate:2 ms all channels
Input Impedance:250 ohms
Input Filter Response:325 Hertz

ALPHANUMERIC DISPLAY COPROCESSOR MODULE

Brand:GE Fanuc
Series:Series 90-30
Part Number:IC693ADC311D
Product Type:Alphanumeric Display Coprocessor Module
Compatible System:CIMPLICITY 90-ADS System
Microprocessor:80C188 Microprocessor
Number of Connectors:1
Number of Serial Ports:2
Soft Configuration:Supported

Slot filler module

Series:Series 90-30
Manufacturer:GE Fanuc
Part Number:IC693ACC310
Product Type:Filler module
Product Description:Slot cover
Ethernet:Supported
Slot width:Single slot
Supported Component:PLC
Rack location:Any slot
Application:Training Simulators
Supply Voltage:None
Item Name:Filler Module
Voltage Rating:120 VAC
No. of module installations:As needed
Amperage Rating:0.5 A

I/O BUS TERMINATOR PLUG

Series:Series 90-30
Part Number:IC693ACC307
Type:Baseplate I/O bus terminator plug
Resistor pack:Yes
I/O expansion cable length:15 meters (50 feet)
Expansion cable:Termination resistors at the end
Category:Automation and control
Compatible components:PLCs
Connector:25-pin

Input Simulator Module

Series:Series 90-30
Part Number:IC693ACC300
Type:I/O module
Number of points:8/16
Power source:DC
Output voltage range:18 to 30 Volts DC
Relative humidity:5 to 95% (non-condensing)
Shock:15 G at 11 milliseconds
Vibration:1 G at 9 to 150 Hertz

Cable Adapter

IC690ACC900
CABLE ADAPTER
RS485/422 TO RS432 CONVERTER
FOR HANDHELD PROGRAMMER

Profibus interface module

Series:Field Control
Manufacturer:GE Fanuc
Part Number:IC670PBI001
Product Type:Profibus Bus Interface
Rated Input Voltage:24 Volts DC
Voltage Range:18-30 Volts DC
Supported Protocols:Profibus
Input Power:7.7 watts
Power Dissipation:4.45 Watts
Addressing:via embedded DIP switches
Holdup Time:10 ms, maximum
Profibus topology:Linear bus topology

DISCRETE OUTPUT MODULE

Series:Field Control
Manufacturer:GE Fanuc
Part Number:IC670MDL930
No of Channels:Eight (8) relay outputs
Frequency Range:47-63 Hertz
Relay Type:Fixed coil, moving armature
Current drawn from BIU:313 mA
LED indicators:Individual channel LED; PWR LED
Switching Frequency:20 cycle/minute
Relay Type::Fixed coil, moving armature
Contact Type:Silver Alloy
Protection:Snubbber, no fuse
Maximum Inrush:5 Amps for 20mS
Minimum Load Current:10 mA per point

DISCRETE OUTPUT MODULE

Series:Field Control
Manufacturer:GE Fanuc
Part Number:IC670MDL740
No. of channels:Sixteen (16)
Output signal, nominal:12/24 VDC
Output Voltage Range:9.2-29.5 Volts DC
Number of Outputs:16
Output current:0.5 A per point; 4 A per module
Number of Groups:1
Group to Group Isolation:None
Current drawn from power supply:111 mA
Output grouping:Single group
Output Voltage Drop:0.5 Volts maximum
Protection:Built-in fuse for group protection;
Output Leakage Current:0.5 mA at 30 VDC

Output Module

Brand:GE Fanuc
Series:Field Control
Part Number:IC670MDL730
Product Description:Discrete Output Module
Output Voltage Range:17.5-29.5 Volts DC
Number of Outputs:8
Number of Groups:1
Group to Group Isolation:None
LED Indicators:3
Current Drawn From Power Supply:125 mA

INPUT MODULE

Series:Field Control
Manufacturer:GE Fanuc
Part Number:IC670MDL640
Rated Voltage:24 Volts DC
Input Voltage Range:0 to 30 Volts DC
No. of channels:Sixteen (16)
Number of Points:16
Input signal, nominal:24 VDC
Current (User Input):7.5 milliamps per point at 24 Volts DC
Input signal, range:0-30 VDC
Input current:7.5 mA
Input Impedance:3K typical
Input grouping:Single group
On-state Current:3.0 mA to 8 mA
Off-state Current:0 to -5VDC

DISCRETE INPUT MODULE

Series:Field Control
Part Number:IC670MDL330
Product Type:Output Module
Number of Outputs:16
Output signal, nominal:12-120 VAC
Discrete Outputs:Yes
Output signal, range:10-132 VAC
Voltage Type:AC
Output current:1 A per point; 4 A per module
Voltage Rating:12 to 120 Volts AC
Current Rating:1 Amp
Discrete Output Data:2 Bytes or 16 Bits
Output grouping:Single group
Output Voltage Drop:2.0 volts maximum

DISCRETE INPUT MODULE

Series:Field Control
Manufacturer:GE Fanuc
No. of channels:Sixteen (16)
Part Number:IC670MDL240
Series:Field I/O control
Input signal, nominal:120 VAC
Product Type:Input Module
Input signal, range:0-132 VAC
Number of Inputs:16
Input current:15 mA at 120 VAC
Voltage Type:AC
No of Channels:Sixteen (16)
Frequency:47 to 63 Hertz
Discrete Input Data:16 Bits (2 Bytes)
Input grouping:Single group
15 mA per channel:77 mA
ON state voltage:70-132 VAC
Nominal input voltage:115 VAC

INTERFACE MODULE

Series:Field Control
Manufacturer:GE Fanuc
Part Number:IC670GBI002
Series:Field I/O control
Type:Bus interface unit
Product Description:Bus Interface Unit (BUI)
Nominal Rated Voltage:115 Volts AC, 125 Volts DC
Supply Voltage range:18-30 VDC
Nominal supply voltage:24 VDC
Frequency:47 to 63 Hertz
Power consumption:16.8 Watts
Inrush Current:15-50 Amps peak, 3 mS maximum
Power Supply Output:6.5 VDC ±5%
Current output to modules:1.4 A
Holdup time:10 ms
Holdup Time:20 milliseconds (maximum)

I/O terminal block

Brand:GE Fanuc
Series:Field Control
Part Number:IC670CHS002
Type of Component:I/O Terminal Block
Number of Terminals:37
Maximum Current on Terminals:10 Amperes
Hot Swap Compatible:Yes
Number of Modules per Block:2 modules

I/O Carrier Module

Series:Field Control
Part Number:IC670CHS001
Type of Component:I/O Base, Barrier Style
Number of Terminals:37
Product Description:I/O Carrier Module
Carrier module terminals:Barrier style
Terminal Torque:8 pounds on an inch
No. of Terminals:37 terminals
No of wires per terminal:up to Two (2) wires
Compatible BIU Version:Bus Interface Unit version 2.1
Tightening torque:8 in-lb.
Mounting DIN:Rail / Panel mount
Mounting orientation:Horizontal

I/O EXPANSION CABLE

Brand:GE Fanuc
Series:Field Control
Part Number:IC670CBL002
Type of Component:Expansion connection cable
ESD Protection:Braided drain wire connected to ground or chassis
Length in Centimeters:54.61
Length in Inches:21
Number of Cables per Field Control Station:1

ANALOG INPUT MODULE

Brand:GE Fanuc
Series:Field Control
Part Number:IC670ALG630
Number of Channels:8
Thermocouple Types:J, K, T, E, S R, B, N, G, C, D, Platinel II
Converter Resolution:15 bits + sign
Maximum Voltage Between Channels:250 VAC
Current Drawn from BIU Power Supply:195 mA maximum

Analog Output Module

Series:Field Control
Manufacturer:GE Fanuc
Wiring configuration:Single-ended
Part Number:IC670ALG330
Output signal, nominal:0-20 mA
Product Type:Output Module
Output signal, range:0.0-20.48 mA
Signal Type:Analog
Current or Voltage Outputs:Current Outputs
Conversion resolution:16 bits
Number of Channels:8
Output load capacitance:2000 pF, maximum
Current Range:0 to 20.48 milliamps
Output load inductance:0.5H, maximum
Number of LEDs:1
Update time:1.5mS typical
Magnitude data size:14 bits
Linearity:1 LSB resolution value
Supply Voltage range:18-30 VDC
Nominal supply voltage:24 VDC
Current draw from Bus Interface Unit (BIU):85 mA
Current drawn from external power:250 mA

Analog Output Module

Series:Field Control
Manufacturer:GE Fanuc
Part Number:IC670ALG320
Wiring configuration:Single-ended
Description:Analog output module
Current:4-20 mA
No of Channels:Four (4) Current / Voltage Source outputs
Voltage:0-10 Volts
Output signals:0-20 mA; 4-20 mA; 0-10 VDC; 0-12.5 VDC
ADC Conversion resolution:12 bits
Output Data:4 words
Isolation:1500 VAC for 1 minute, 250 VAC continuous
External Power supply:20-29 VDC, 5 % maximum ripple
Isolation to Ground and Logic:1500 Volts AC
Nominal Supply voltage:24 VDC
Digital Resolution:12 bits, typical
Linearity:1 LSB resolution value
Current Drawn from BIU power supply:51 mA, maximum
Input Types:Isolated and Differential
Output grouping:Single group
Output wiring:Single-ended

ANALOG INPUT MODULE

Series:Field Control
Manufacturer:GE Fanuc
Part Number:IC670ALG240
Description:Analog input module
Channels:16
Input Current:0-25 milliamperes
Wiring configuration:Single-ended
Frequency:50/60 Hertz
Input signal, nominal:0-20 mA
Input signal, range:0.0-20.48 mA
Ripple:10% max.
Maximum current input:35 mA
Common Mode Rejection:86 dB
ADC Conversion resolution:16 bits
Hardware Filter:RC 2nd order
External Power supply:20-28 VDC
Nominal Supply voltage:24 VDC
Input grouping:Single group

CURRENT SOURCE ANALOG INPUT MODULE

Series:Field Control
Manufacturer:GE Fanuc
Part Number:IC670ALG230
No. of channels:Eight (8)
Description:Input module
Wiring configuration:Single-ended
Input signal, nominal:0-20 mA
Isolation to Case:250 Volts AC continuous
Input signal, range:0.0-25 mA mA
Input Impedance:2.87 kiloohms
Analog resolution:5.0 µA
On-state Voltage:15-30 Volts DC
Conversion resolution:12 bits
Off-state Voltage:0-5 Volts DC
External Power supply:18-30 VDC
Current from BIU:100 milliamperes
Analog resolution:5.0 microAmps
Nominal Supply voltage:24 VDC
Input Impedance:249.75 to 250.25 Ohms
Input grouping:Single group

Genius Block I/O module

Brand:GE Fanuc
Series:Genius I-O
Part Number:IC660TSS100
Product Type:Terminal assembly
Storage Temperature:-40 to 212 degrees Fahrenheit
Relative Humidity:5 to 95%
Vibration:5 to 10 Hertz

Genius Block I/O module

Series:Genius I-O
Part Number:IC660TSD100
Product Type:Terminal assembly
Operating Temperature:32 to 140 degrees Fahrenheit
Number of Circuits per I/O Block:8
Supported Memory:EEPROM

Genius Block I/O module

Brand:GE Fanuc
Series:Genius I-O
Part Number:IC660TSD021
Product Type:Terminal assembly
Compatibility:IC660BBD021 I/O Block
Solid-State Sensors:Supported
Relative Humidity:5 to 95%
Input Filter Time:5 to 100 milliseconds